Why Is There a Gap Behind the Brick?

Why Is It Built That Way? | Article 2

If you walk up to your house while the brick is going on, you might notice something that looks a little suspicious. The bricklayer is building a wall, and there’s a gap between the brick and the house.
Then a piece of mortar falls into it.
Now you have two questions: “Why is there a gap?” and “Is that mortar supposed to be back there?”
On a typical brick veneer house, the gap is intentional. Some mortar will fall into it during construction, and a few droppings don’t mean the wall was built wrong. What matters is that mortar and debris don’t block the path water needs to get out.
In other words, the space doesn’t have to be spotless. It does have to work.
What Does the Gap Behind Brick Do?
On many homes, the brick you see from the street is a veneer. It’s an outer layer of masonry tied back to the structure. Between that brick and the wall behind it is a space that gives water a way to drain.
Yes, water can get behind brick. A hard, wind-driven rain can push moisture through the brickwork, even when the wall looks fine from the driveway. The wall is built with that possibility in mind.
The layer behind the brick helps protect the house from water. The space gives water room to run down. Flashing catches it at places like the base of the wall and directs it out through openings called weep holes.
If you read the first article in this series, you already know what those little holes do. The weep holes are the exits. The gap behind the brick is how water gets to them.
That’s why seeing open weep holes from the outside only tells you part of the story. An exit can look perfectly clear from the street and still be blocked on the other side.
Is Mortar Behind the Brick Normal?
Yes, some is. When a bricklayer sets a brick into fresh mortar, a little can squeeze out the back. Small pieces can also drop while the crew is working. That comes with laying brick.
A few clumps that leave enough room for water to drain are very different from a ridge of hardened mortar piled across the bottom of a wall. That ridge can act like a dam. Mortar can also build up enough to touch both the brick and the wall behind it, giving moisture a route across the space that was supposed to keep those surfaces apart.
The cavity doesn’t have to be filled all the way up to cause trouble. A buildup in the wrong spot can block drainage while most of the space above it is still open.
And then there’s the stuff that never needed to be there in the first place. Packaging, water bottles , and other jobsite trash don’t belong behind the wall. “Nobody can see it” is a pretty low standard for work that’s about to be covered up.
What Keeps the Drainage Path Clear?
Good brickwork starts with controlling how much mortar squeezes out and falls behind the wall. It also means paying attention to what collects below, especially around flashing and weep holes.
Some wall designs use a mortar collection product. It catches and spreads out droppings so they’re less likely to pile up right at the outlets. It’s useful when installed correctly, but it doesn’t replace good workmanship or make the space a handy place to drop trash.
The best time to look at any of this is while the wall is going up. Once the brick is finished, you can see the face of the wall and the weep openings. You generally can’t see whether the flashing behind them has a clear path to drain. And no, a nice straight mortar joint on the front won’t tell you what happened in the back.
What Should a Homeowner Ask?
If your house is under construction, ask your builder or mason to show you where the water is supposed to go. You don’t need to memorize a wall detail. A few plain questions will tell you more than staring at the brick from the driveway:
Where is the flashing, and where will the water come out?
How are you keeping mortar from building up at the bottom?
Can we get a few photos of the flashing and the space behind the brick before they’re covered?
If you spot a little mortar behind the brick, don’t assume you caught a mistake. Ask how the crew keeps the drainage path open. If you see a section packed with mortar or debris, bring it up while the crew can still see and address it.
On an existing home, recurring dampness or staining is a reason to find out where the water is coming from. It doesn’t automatically mean that mortar blocked the cavity.
Windows, roof details, and other parts of the house can also let water in. Figuring out the route first can save you from paying for a repair in the wrong place.
The next time you see a gap behind brick veneer, leave it room to do its job. A little dropped mortar is part of laying brick. Giving the water somewhere to go is part of building the wall.



Comments